added launch script, config an systemd unit file.
This commit is contained in:
89
config/config.txt
Executable file
89
config/config.txt
Executable file
@@ -0,0 +1,89 @@
|
||||
# For more options and information see
|
||||
# http://rpf.io/configtxt
|
||||
# Some settings may impact device functionality. See link above for details
|
||||
|
||||
[all]
|
||||
# uncomment if you get no picture on HDMI for a default "safe" mode
|
||||
#hdmi_safe=1
|
||||
|
||||
# uncomment the following to adjust overscan. Use positive numbers if console
|
||||
# goes off screen, and negative if there is too much border
|
||||
#overscan_left=16
|
||||
#overscan_right=16
|
||||
#overscan_top=16
|
||||
#overscan_bottom=16
|
||||
|
||||
# uncomment to force a console size. By default it will be display's size minus
|
||||
# overscan.
|
||||
#framebuffer_width=1280
|
||||
#framebuffer_height=720
|
||||
|
||||
# uncomment if hdmi display is not detected and composite is being output
|
||||
#hdmi_force_hotplug=1
|
||||
|
||||
# uncomment to force a specific HDMI mode (this will force VGA)
|
||||
#hdmi_group=1
|
||||
#hdmi_mode=1
|
||||
|
||||
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
||||
# DMT (computer monitor) modes
|
||||
#hdmi_drive=2
|
||||
|
||||
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
||||
# no display
|
||||
#config_hdmi_boost=4
|
||||
|
||||
# uncomment for composite PAL
|
||||
#sdtv_mode=2
|
||||
|
||||
#uncomment to overclock the arm. 700 MHz is the default.
|
||||
#arm_freq=800
|
||||
#arm_freq=2000
|
||||
|
||||
# Uncomment some or all of these to enable the optional hardware interfaces
|
||||
#dtparam=i2c_arm=on
|
||||
#dtparam=i2s=on
|
||||
#dtparam=spi=on
|
||||
|
||||
# Uncomment this to enable infrared communication.
|
||||
#dtoverlay=gpio-ir,gpio_pin=17
|
||||
#dtoverlay=gpio-ir-tx,gpio_pin=18
|
||||
|
||||
# Additional overlays and parameters are documented /boot/overlays/README
|
||||
|
||||
# Enable audio (loads snd_bcm2835)
|
||||
dtparam=audio=on
|
||||
|
||||
# Automatically load overlays for detected cameras
|
||||
camera_auto_detect=1
|
||||
|
||||
# Automatically load overlays for detected DSI displays
|
||||
display_auto_detect=1
|
||||
|
||||
# Enable DRM VC4 V3D driver
|
||||
dtoverlay=vc4-kms-v3d
|
||||
max_framebuffers=2
|
||||
|
||||
# Disable compensation for displays with overscan
|
||||
disable_overscan=1
|
||||
|
||||
[cm4]
|
||||
# Enable host mode on the 2711 built-in XHCI USB controller.
|
||||
# This line should be removed if the legacy DWC2 controller is required
|
||||
# (e.g. for USB device mode) or if USB support is not required.
|
||||
otg_mode=1
|
||||
|
||||
|
||||
[pi4]
|
||||
# Run as fast as firmware / board allows
|
||||
arm_boost=1
|
||||
|
||||
[fan]
|
||||
fan_temp0_temp=55
|
||||
fan_temp0_speed=0
|
||||
fan_temp1_temp=60
|
||||
fan_temp1_speed=50
|
||||
fan_temp2_temp=70
|
||||
fan_temp2_speed=100
|
||||
|
||||
|
||||
16
systemd/system/fanctrl.service
Normal file
16
systemd/system/fanctrl.service
Normal file
@@ -0,0 +1,16 @@
|
||||
[Unit]
|
||||
Description=Control the Ultra Light ICE-Tower Cooler fan
|
||||
After=network.service
|
||||
|
||||
[Service]
|
||||
Type=simple
|
||||
#WorkingDirectory=/home/pi/git/fanctrl
|
||||
ExecStart=/usr/local/bin/fanctrl
|
||||
StandardOutput=append:/var/log/fanctrl.log
|
||||
StandardError=append:/var/log/fanctrl_error.log
|
||||
Restart=no
|
||||
|
||||
|
||||
[Install]
|
||||
WantedBy=multi-user.target
|
||||
|
||||
15
usr/local/bin/fanctrl
Executable file
15
usr/local/bin/fanctrl
Executable file
@@ -0,0 +1,15 @@
|
||||
#! /bin/bash
|
||||
|
||||
cleanup() {
|
||||
echo "cleanup()"
|
||||
echo "terminating ${FANCTRL_PID}"
|
||||
kill -TERM "${FANCTRL_PID}"
|
||||
}
|
||||
|
||||
trap cleanup exit
|
||||
|
||||
cd /home/pi/git/fanctrl
|
||||
exec /home/pi/.local/bin/uv run ./fanctrl.py &
|
||||
FANCTRL_PID=$!
|
||||
echo "FANCTRL_PID=${FANCTRL_PID}"
|
||||
wait "${FANCTRL_PID}"
|
||||
Reference in New Issue
Block a user